Search Results - Case Colt Ingersoll Lawn and Garden Tractor Forum

Search:

Type: Posts; User: Bob MacGregor

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    15
    Views
    1,007

    Yes, 5-6" from the top of the fill.

    Yes, 5-6" from the top of the fill.
  2. Replies
    1
    Views
    106

    A few questions, what is the PIN number of your...

    A few questions, what is the PIN number of your 446? How did you determine that the hydraulic pump needs to be replaced?
    The pump has a high pressure output hose as you know and it has a suction...
  3. A J50 blade is 44" wide, it will fit on 200, 400,...

    A J50 blade is 44" wide, it will fit on 200, 400, 3000 and 4000 series tractors, but not recommended for use on 400 and 4000 series tractors as these tractors are wider than 200 and 3000 tractors....
  4. Vanguard twins do not have a removable oil base....

    Vanguard twins do not have a removable oil base. I would make sure that you have the correct dipstick tube and dipstick.:geek:
  5. Operators manual for newer 4018-4223 non PS...

    Operators manual for newer 4018-4223 non PS models....
  6. Replies
    5
    Views
    450

    Crazy mixed up looking rig! I hope they install...

    Crazy mixed up looking rig! I hope they install the cooling tins over the cylinder heads. These engines have a tendency for the valves to stick and being L head engines, cleaning up the valve guides...
  7. Replies
    15
    Views
    1,007

    I am having some tubes made up at a local...

    I am having some tubes made up at a local hydraulics shop, when I receive them I will post the info and pics in Mac's Corner on this forum.:geek:
  8. Replies
    15
    Views
    1,007

    Our engines burn oil while running and have a...

    Our engines burn oil while running and have a dipstick to monitor the oil level.
    The hydraulic system, once it is fully operated and topped up to the correct oil level, will stay at that level...
  9. Replies
    31
    Views
    1,714

    Under the battery rack is the hydraulic oil...

    Under the battery rack is the hydraulic oil cooler, it can get very dirty. Blow it out from under the steering tower toward the engine. All of the oil for moving the tractor goes thru the PTO valve...
  10. Replies
    29
    Views
    2,185

    Hi guys, Here is a pic of the governor spring...

    Hi guys,
    Here is a pic of the governor spring setup on the B43M that I have here. Normal idle speed and 3,300 RPM at full throttle. I will increase it to 3,600 after I reinstall the engine.
    115481
  11. Replies
    22
    Views
    1,347

    Starter motor has one slotted mounting bolt hole...

    Starter motor has one slotted mounting bolt hole to allow the starter gear to be correctly adjusted to the flywheel ring gear. If the starter is installed tight toward the engine in the slotted hole,...
  12. B43M & B48M breaker points adjust and timing check

    Hi Troops,
    Owner of this 226 asked me to check the starter motor installation. As I had the muffler and pipes off, I removed the blower housing to check the starter motor. I had previously cleaned...
  13. 226, 446 and 448 Onan powered tractor clutch...

    226, 446 and 448 Onan powered tractor clutch info, more to come!:geek:
    115377115379115385115381115383
    115391
  14. Replies
    14
    Views
    927

    Hi case3016, On the R/H side of the blower...

    Hi case3016,
    On the R/H side of the blower housing is the engine data plate, the 3rd group of numbers is the date code. The first two numbers is the year of manufacture, the next two numbers is the...
  15. Replies
    8
    Views
    463

    Differential bolt in the transaxle? Inspect the...

    Differential bolt in the transaxle? Inspect the bottom of the transaxle for cracks and holes. Jack up the tractor, remove the R/H rear wheel, remove the lower plug and drain the transaxle oil. Check...
  16. Replies
    24
    Views
    1,509

    There is a notch cutout on the points cover for...

    There is a notch cutout on the points cover for the wire to the coil to pass thru.
    The insulation on the coil wire in the pic had been cut from not lining up the coil wire with the notch when it was...
  17. Onan B43M, B48M and P series in re powers

    Hi Troops,
    Over the years the intake manifold bolt threads in the engine get stripped. When the Case/Ingersoll heat shields are installed with lock and flat washers the stock bolts don't engage...
  18. Problem with B43M and B48M Onan engine dipsticks

    Hi Troops,
    As time passes, the dipsticks on these engines wear in a critical spot. These dipsticks, Onan P/N 123-1292 have been discontinued by Cummins/Onan and new ones are in very short supply!...
  19. Replies
    0
    Views
    135

    Snap Fast pins upgrade

    Hi Troops,
    This upgrade pertains to all tractors with 'Snap Fast' locking pins.
    The stock roll pins are 3/16" X 1 1/4", I replace these with new roll pins that are 3/16" X 1 1/2". This makes the...
  20. EZ adjust clutch info coming soon in Mac's Corner

    Hi Troops,
    The 226 that I have here also needs clutch repairs, installation and adjustment. When the parts order arrives next week I hope, I will do pics and procedure with an EZ adjust clutch. ...
  21. Replies
    25
    Views
    1,927

    Hi Moostang, Your transaxle doesn't have the 2nd...

    Hi Moostang,
    Your transaxle doesn't have the 2nd level plug, so put at least a pint of oil or more in while you have it open.
    Early models of some tractors used the transaxle oil in the hydraulic...
  22. Pics of pulse hose on a B43M, B48M with Nikki...

    Pics of pulse hose on a B43M, B48M with Nikki carb and blower housing mounted fuel pump. On Onan powered 226, 446 and 448, the fuel line goes thru the hole in the crossmember by the fuel tank, passes...
  23. Hi Troops, I have a members 1986 226 here for...

    Hi Troops,
    I have a members 1986 226 here for much TLC. Primary problem was contamination on the carb and fuel system. I'm not sure what the stuff was that was in the carb, but it was blocking fuel...
  24. All horizontal shaft Vanguards have cast aluminum...

    All horizontal shaft Vanguards have cast aluminum valve covers and I have never seen any that had the model numbers stamped into them.
    The newer series of vertical shaft Vanguards are spinoffs of...
  25. The Briggs part number on the carb would better...

    The Briggs part number on the carb would better identify the engine as an 18.
    Your engine likely is a 356447-3079-G1. you can look up the parts manual for this engine on the Briggs website to get...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4